View MAX461307_4127841.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

19-1362; Rev 3; 6/07
Quad, SPST Analog Switch
________________General Description
The MAX4613 quad analog switch features on-resistance matching (4 max) between switches and guarantees on-resistance flatness over the signal range (9 max). This low on-resistance switch conducts equally well in either direction. It guarantees low charge injection (10pC max), low power consumption (35W max), and an electrostatic discharge (ESD) tolerance of 2000V minimum per Method 3015.7. The new design offers lower off-leakage current over temperature (less than 5nA at +85C). The MAX4613 quad, single-pole/single-throw (SPST) analog switch has two normally closed switches and two normally open switches. Switching times are less than 250ns for t ON and less than 70ns for t OFF . Operation is from a single +4.5V to +40V supply or bipolar 4.5V to 20V supplies.
____________________________Features
Pin Compatible with Industry-Standard DG213 Guaranteed RON Match Between Channels (4 max) Guaranteed RFLAT(ON) Over Signal Range (9 max) Guaranteed Charge Injection (10pC max) Low Off-Leakage Current Over Temperature (<5nA at +85C) Withstands 2000V min ESD, per Method 3015.7 Low RDS(ON) (85 max) Single-Supply Operation +4.5V to +40V Bipolar-Supply Operation 4.5V to 20V Low Power Consumption (35W max) Rail-to-Rail Signal Handling TTL/CMOS-Logic Compatible
MAX4613
________________________Applications
Sample-and-Hold Circuits Test Equipment Heads-Up Displays Guidance and Control Systems Military Radios Communication Systems Battery-Operated Systems PBX, PABX Audio Signal Routing Modems/Faxes
Pin Configurations/ ___Functional Diagrams/TruthTable ________________Ordering Information
IN2
IN1
D1
D2
TOP VIEW
PART MAX4613CPE MAX4613CSE
12 S2 11 V+
TEMP RANGE 0C to +70C 0C to +70C 0C to +70C 0C to +70C 0C to +70C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C
PIN-PACKAGE 16 Plastic DIP 16 Narrow SO 16 QSOP 16 TSSOP** Dice* 16 TQFN-EP*** (5mm x 5mm) 16 Plastic DIP 16 Narrow SO 16 QSOP 16 TSSOP**
16
15
14
13
S1 1 V- 2
MAX4613CEE MAX4613CUE MAX4613CC/D MAX4613ETE MAX4613EPE MAX4613ESE MAX4613EEE MAX4613EUE
MAX4613
GND 3 *EP S4 4
5 6 IN4 7 8 D3 9 S3 10 VL
D4
THIN QFN
*EP = EXPOSED PAD, CONNECT EP TO V+
IN3
*Contact factory for dice specifications. **Contact factory for availability. ***EP = Exposed Pad
Pin Configurations continued at end of data sheet.
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com.
Quad, SPST Analog Switch MAX4613
ABSOLUTE MAXIMUM RATINGS
Voltage Referenced to GND V+ ......................................................................................+44V V-.........................................................................................-44V V+ to V- ..............................................................................+44V VL ...................................................(GND - 0.3V) to (V+ + 0.3V) Digital Inputs VS_ VD_ (Note 1) ...................(V- - 2V) to (V+ + 2V) or 30mA (whichever occurs first) Continuous Current (any terminal) ......................................30mA Peak Current, S_ or D_ (pulsed at 1ms, 10% duty cycle max) ...........................100mA Continuous Power Dissipation (TA = +70C) Plastic DIP (derate 10.53mW/C above +70C) .............842mW Narrow SO (derate 8.70mW/C above +70C) .............696mW QSOP (derate 8.3mW/C above +70C) .......................667mW Thin QFN (derate 33.3mW/C above +70C)..............2667mW TSSOP (derate 6.7mW/C above +70C) .....................457mW Operating Temperature Ranges MAX4613C_ _ ......................................................0C to +70C MAX4613E_ _ ...................................................-40C to +85C Storage Temperature Range .............................-65C to +165C Lead Temperature (soldering, 10sec) .............................+300C
Note 1: Signals on S_, D_, or IN_ exceeding V+ or V- are clamped by internal diodes. Limit forward current to maximum current rating.
Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS--Dual Supplies
(V+ = 15V, V- = -15V, VL = 5V, GND = 0V, VINH = 2.4V, VINL = 0.8V, TA = TMIN to TMAX, unless otherwise noted.) PARAMETER SWITCH Analog Signal Range Drain-Source On-Resistance On-Resistance Match Between Channels (Note 4) VANALOG RDS(ON) RDS(ON) (Note 3) VD = 10V, IS = 1mA VD = 10V, IS = 1mA TA = +25C TA = TMIN to TMAX TA = +25C TA = TMIN to TMAX TA = +25C TA = TMIN to TMAX TA = +25C TA = TMIN to TMAX TA = +25C TA = TMIN to TMAX TA = +25C TA = TMIN to TMAX -0.50 -5 -0.50 -5 -0.50 -10 0.08 0.01 0.01 -15 55 15 70 85 4 5 9 15 0.50 5 0.50 5 0.50 nA 10 V nA nA SYMBOL CONDITIONS MIN TYP (Note 2) MAX UNITS
VD = 5V, On-Resistance Flatness (Note 4) RFLAT(ON) IS = 1mA Source Leakage Current (Note 5) Drain-Off Leakage Current (Note 5) Drain-On Leakage Current (Note 5) INPUT Input Current with Input Voltage High Input Current with Input Voltage Low SUPPLY Power-Supply Range Positive Supply Current Negative Supply Current V+, VI+ IAll channels on or off, VIN = 0 or 5V All channels on or off, VIN = 0 or 5V IINH IINL IS(OFF) ID(OFF) ID(ON) or IS(ON) VD = 14V, VS = 14V VD = 14V, VS = 14V VD = 14V, VS = 14V
VIN = 2.4V, all others = 0.8V VIN = 0.8V, all others = 2.4V
-0.5 -0.5
-0.00001 -0.00001
0.5 0.5
A A
4.5 TA = +25C TA = TMIN to TMAX TA = +25C TA = TMIN to TMAX -1 -5 -1 -5 0.001 0.001
20.0 1 5 1 5
V A A
2
_______________________________________________________________________________________
Quad, SPST Analog Switch
ELECTRICAL CHARACTERISTICS--Dual Supplies (continued)
(V+ = 15V, V- = -15V, VL = 5V, GND = 0V, VINH = 2.4V, VINL = 0.8V, TA = TMIN to TMAX, unless otherwise noted.) PARAMETER Logic Supply Current Ground Current DYNAMIC Turn-On Time (Note 3) Turn-Off Time (Note 3) Break-Before-Make Time Delay (Note 3) Charge Injection (Note 3) Off-Isolation Rejection Ratio (Note 6) Crosstalk (Note 7) Source-Off Capacitance Drain-Off Capacitance Source-On Capacitance Drain-On Capacitance CS(OFF) CD(OFF) CS(ON) CD(ON) tON tOFF tD Q OIRR VS = 10V, Figure 2 VS = 10V, Figure 2 Figure 3 CL = 1nF, VGEN = 0, RGEN = 0, Figure 4 RL = 50, CL = 5pF, f = 1MHz, Figure 5 RL = 50, CL = 5pF, f = 1MHz, Figure 6 f = 1MHz, Figure 7 f = 1MHz, Figure 7 f = 1MHz, Figure 8 f = 1MHz, Figure 8 TA = +25C TA = +25C TA = +25C TA = +25C TA = +25C TA = +25C TA = +25C TA = +25C TA = +25C TA = +25C 5 150 90 20 5 60 100 4 4 16 16 10 250 120 ns ns ns pC dB dB pF pF pF pF SYMBOL IL IGND CONDITIONS All channels on or off, VIN = 0 or 5V All channels on or off, VIN = 0 or 5V TA = +25C TA = TMIN to TMAX TA = +25C TA = TMIN to TMAX MIN -1 -5 -1 -5 -0.0001 TYP (Note 2) 0.001 MAX 1 5 1 5 UNITS A A
MAX4613
ELECTRICAL CHARACTERISTICS--Single Supply
(V+ = 12V, V- = 0V, VL = 5V, GND = 0V, VINH = 2.4V, VINL = 0.8V, TA = TMIN to TMAX, unless otherwise noted.) PARAMETER SWITCH Analog Signal Range Drain-Source On-Resistance SUPPLY Power-Supply Range Power-Supply Current Negative Supply Current Logic Supply Current Ground Current V+, VI+ IIL IGND All channels on or off, VIN = 0 or 5V All channels on or off, VIN = 0 or 5V All channels on or off, VIN = 0 or 5V All channels on or off, VIN = 0 or 5V TA = +25C TA = TMIN to TMAX TA = +25C TA = TMIN to TMAX TA = +25C TA = TMIN to TMAX TA = +25C TA = TMIN to TMAX 4.5 -1 -5 -1 -5 -1 -5 -1 -5 -0.0001 0.001 -0.0001 0.001 40 1 5 1 5 1 5 1 5 V A A A A VANALOG RDS(ON) VL = 5V; VD = 3V, 8V; IS = 1mA TA = +25C TA = TMIN to TMAX 0 100 12 160 200 V SYMBOL CONDITIONS MIN TYP (Note 2) MAX UNITS
_______________________________________________________________________________________
3
Quad, SPST Analog Switch MAX4613
ELECTRICAL CHARACTERISTICS--Single Supply (continued)
(V+ = 12V, V- = 0, VL = 5V, GND = 0V, VINH = 2.4V, VINL = 0.8V, TA = TMIN to TMAX, unless otherwise noted.) PARAMETER DYNAMIC Turn-On Time (Note 3) Turn-Off Time (Note 3) Charge Injection (Note 3) tON tOFF Q VS = 8V, Figure 2 VS = 8V, Figure 2 CL = 1nF, VGEN = 0, RGEN = 0, Figure 4 TA = +25C TA = +25C TA = +25C 300 60 5 400 200 10 ns ns pC SYMBOL CONDITIONS MIN TYP (Note 2) MAX UNITS
Note 2: Typical values are for design aid only, are not guaranteed and are not subject to production testing. The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in this data sheet. Note 3: Guaranteed by design. Note 4: On-resistance match between channels and flatness are guaranteed only with bipolar-supply operation. Flatness is defined as the difference between the maximum and the minimum value of on-resistance as measured at the extremes of the specified analog signal range. Note 5: Leakage parameters IS(OFF), ID(OFF), ID(ON), and IS(ON) are 100% tested at the maximum rated hot temperature and guaranteed at +25C. Note 6: Off-Isolation Rejection Ratio = 20log (VD/VS). Note 7: Between any two switches.
__________________________________________Typical Operating Characteristics
(TA = +25C, unless otherwise noted.)
ON LEAKAGE CURRENTS
MAX4613-01
OFF LEAKAGE CURRENTS
MAX4613-02
SWITCHING THRESHOLD vs. BIPOLAR SUPPLY VOLTAGE
MAX4613-03
2
1
3.5 3.0 2.5 IN HIGH MIN
1 ON LEAKAGE (nA) OFF LEAKAGE (nA) TA = +125C 0
0.5
TA = +125C
0
VIN (V)
TA = +85C
TA = +85C
2.0 1.5
-1 V+ = 15V V- = -15V -2 -15 -10 -5 0 VS, VD (V) 5 10 15
-0.5 V+ = 15V V- = -15V -15 -10 -5 0 VS, VD (V) 5 10 15 0.5 0 5 10
IN LOW MAX
-1
15
20
BIPOLAR SUPPLY VOLTAGE (V)
ON-RESISTANCE vs. VD (UNIPOLAR SUPPLY VOLTAGE)
MAX4613-04
ON-RESISTANCE vs. VD (BIPOLAR SUPPLY VOLTAGE)
MAX4613-05
ON-RESISTANCE vs. VD (BIPOLAR SUPPLY VOLTAGE AND TEMPERATURE)
V+ = 15V, V- = -15V
MAX4613-06
150 V+ = 5V 125 V+ = 10V 100 RDS(ON) ()
120 V = 5V 90 RDS(ON) () V = 10V 60 V = 15V 30 V = 20V
100
80 TA = +125C TA = +25C TA = -55C 20
V+ = 15V 75 50 25 0 0 5 10 VD (V) 15 20 V+ = 20V
RDS(ON) ()
60
40
0 -20 -10 0 VD (V) 10 20
0 -15
-10
-5
0 VD (V)
5
10
15
4
_______________________________________________________________________________________
Quad, SPST Analog Switch
_____________________________Typical Operating Characteristics (continued)
(TA = +25C, unless otherwise noted.)
ON-RESISTANCE vs. VD (UNIPOLAR SUPPLY VOLTAGE AND TEMPERATURE)
MAX4613-07
MAX4613
SWITCHING TIME vs. BIPOLAR SUPPLY VOLTAGE
MAX4613-08
SWITCHING TIME vs. UNIPOLAR SUPPLY VOLTAGE
V- = 0 150 TIME (ns)
MAX4613-09
150 TA = +125C 125 100 RDS(ON) () 75 50 TA = +25C
160
200
120 tON TIME (ns)
TA = -40C
80
100
tON
40 25 0 0 4 VD (V) 8 12 V+ = 12V V- = 0 0 5 10 15 20 BIPOLAR SUPPLY VOLTAGE (V) tOFF
50
tOFF
0 10 15 20 UNIPOLAR SUPPLY VOLTAGE (V) 25
CHARGE INJECTION vs. VD VOLTAGE
MAX4613-10
CHARGE INJECTION vs. VD VOLTAGE
V+ = 12V V- = 0V CL = 1nF
MAX4613-11
20 V+ = 15V V- = -15V CL = 1nF 10
10
5
Q (pC)
0
Q (pC) -15 -10 0 VD (V) 10 15
0
-10
-5
-20
-10 0 5 VD (V) 10 15
_______________________________________________________________________________________
5
Quad, SPST Analog Switch MAX4613
Pin Description
PIN DIP/SO/TSSOP 1, 8, 9, 16 2, 7, 10, 15 3, 6, 11, 14 4 5 12 13 -- THIN QFN 6, 7, 14, 15 5, 8, 13, 16 1, 4, 9, 12 2 3 10 11 EP NAME IN1-IN4 D1-D4 S1-S4 VGND VL V+ PAD Logic Control Input Analog-Switch Drain Output Analog-Switch Source Output Negative-Supply Voltage Input Ground Logic-Supply Voltage Input Positive-Supply Voltage Input--Connected to Substrate Exposed Pad. Connect PAD to V+. FUNCTION
Applications Information
General Operation
1) Switches are open when power is off. 2) IN_, D_, and S_ should not exceed V+ or V-, even with the power off. 3) Switch leakage is from each analog switch terminal to V+ or V-, not to other switch terminals.
VL, V-, and logic inputs. If power-supply sequencing is not possible, add two small, external signal diodes in series with supply pins for overvoltage protection (Figure 1). Adding diodes reduces the analog signal range to 1V below V+ and 1V above V-, but low switch resistance and low leakage characteristics are unaffected. Device operation is unchanged, and the difference between V+ and Vshould not exceed +44V.
Operation with Supply Voltages Other than 15V
Using supply voltages less than 15V will reduce the analog signal range. The MAX4613 operates with 4.5V to 20V bipolar supplies or with a +4.5V to +40V single supply; connect V- to GND when operating with a single supply. Also, all device types can operate with unbalanced supplies such as +24V and -5V. VL must be connected to +5V to be TTL compatible, or to V+ for CMOS-logic level inputs. The Typical Operating Characteristics graphs show typical on-resistance with 20V, 15V, 10V, and 5V supplies. (Switching times increase by a factor of two or more for operation at 5V.)
V+
S
D
Vg
V-
Overvoltage Protection
Proper power-supply sequencing is recommended for all CMOS devices. Do not exceed the absolute maximum ratings because stresses beyond the listed ratings may cause permanent damage to the devices. Always sequence V+ on first, followed by
Figure 1. Overvoltage Protection Using External Blocking Diodes
6
_______________________________________________________________________________________
Quad, SPST Analog Switch
Timing Diagrams/Test Circuits
LOGIC INPUT +3V 50% 0V tOFF VOUT 0.8 x VOUT SWITCH OUTPUT 0V tON 0.8 x VOUT SWITCH OUTPUT t f < 20ns t r < 20ns LOGIC INPUT +3V 50% 0V VD 0V VD VO2 SWITCH OUTPUT 0V tD +5V +15V tD 0.9VO VO1 0.9VO
MAX4613
LOGIC INPUT WAVEFORM IS INVERTED FOR SWITCHES THAT HAVE THE OPPOSITE LOGIC SENSE. +5V SWITCH INPUT VL D_ IN_ LOGIC INPUT +3V GND V-15V REPEAT TEST FOR CHANNELS 2, 3, AND 4. CL INCLUDES FIXTURE AND STRAY CAPACITANCE. VOUT = VD RL CL LOGIC INPUT +15V V+ S_
VL
MAX4613
VOUT
VD = 10V VD = 10V
D_ D_ IN_ GND
V+ S_ S_
MAX4613
VO2 RL2 RL1
VO1
CL1 VCL2
( RL + RDS(ON) )
RL
0V
-15V
RL = 1000 CL = 35pF
CL INCLUDES FIXTURE AND STRAY CAPACITANCE. LOGIC 0 INPUT.
Figure 2. Switching Time
Figure 3. Break-Before-Make Test Circuit
____________________Revision History
Pages changed at Rev 3: 1, 9, 10
_______________________________________________________________________________________
7
Quad, SPST Analog Switch MAX4613
_________________________________Timing Diagrams/Test Circuits (continued)
VOUT
10nF
+15V
+5V
MAX4613
VOUT
SIGNAL GENERATOR
10dBm
D_ V+ IN_
VL
S_
50
RGEN = 50 0 or +2.4V IN_ 0 or +2.4V
VIN Q = VOUT x CL
NETWORK ANALYZER RL
S_ GND V-
D_ 10nF
+5V VL S_ VGEN GND IN_
+15V V+ D_
-15V
RGEN
MAX4613
VOUT CL
Figure 6. Crosstalk
V-15V VIN = +3V
10nF
+15V
+5V
MAX4613
D_ V+
VL
IN_
Figure 4. Charge Injection
CAPACITANCE METER f = 1MHz
0 or +2.4V
S_ GND V10nF
10nF
+15V
+5V
-15V
MAX4613 Figure 7. Source/Drain-Off Capacitance
SIGNAL GENERATOR
10dBm
D_ V+
VL +15V +5V
RGEN = 50 IN_ 0 or +2.4V NETWORK ANALYZER RL -15V S_ GND V10nF CAPACITANCE METER f = 1MHz VS S_ 10nF
MAX4613
D_ V+
VL
IN_
0 or +2.4V
Figure 5. Off-Isolation Rejection Ratio
GND
V-
10nF
-15V
Figure 8. Source/Drain-On Capacitance 8 _______________________________________________________________________________________
Quad, SPST Analog Switch
Pin Configurations (continued)
TOP VIEW
IN1 D1 S1 VGND S4 D4 IN4 1 2 3 4 5 6 7 8 16 15 14 13 IN2 D2 S2 V+ VL S3 D3 IN3
MAX4613
MAX4613
12 11 10 9
DIP/SO/QSOP/TSSOP
LOGIC 0 1 SW1, SW4 OFF ON SW2, SW3 ON OFF
SWITCHES SHOWN FOR LOGIC "0" INPUT
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.)
TSSOP4.40mm.EPS
PACKAGE OUTLINE, TSSOP 4.40mm BODY
21-0066
I
1 1
_______________________________________________________________________________________
9
Quad, SPST Analog Switch MAX4613
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.)
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
10 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 2007 Maxim Integrated Products is a registered trademark of Maxim Integrated Products.
QFN THIN.EPS

▲Up To Search▲

Price & Availability of MAX461307

	To Download MAX461307 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .